This is achieved by burning off the excess hydrocarbons which result from the extra-rich mixture required for a cold start. Slightly lean of stoichiometric, the exhaust gases from the engine contain excess oxygen, the production of NOx by the engine increases, and the efficiency of the catalyst at reducing NOx falls off rapidly. However, the conversion of HC and CO is very efficient due to the available oxygen, oxidizing to H2O and CO2. However, the efficiency of the catalyst at reducing NOx is good, and the production of NOx by the engine decreases.

Although phosphorus is no longer used in gasoline, it (and zinc, another low-level catalyst contaminant) was widely used in engine oil antiwear additives such as zinc dithiophosphate (ZDDP). Beginning in 2004, a limit of phosphorus concentration in engine oils was adopted in the API SM and ILSAC GF-4 specifications. Although catalytic converters are most commonly applied to exhaust systems in automobiles, they are also used on electrical generators, forklifts, mining equipment, trucks, buses, locomotives, motorcycles, and on ships. They are even used on some wood stoves to control emissions.[5] This is usually in response to government regulation, either through environmental regulation or through health and safety regulations. Custom setups, especially for vehicles that do a lot of off-roading are also available.

The cat back system’s pipes have a larger diameter than a standard set. So, your vehicle will get to perform better at a fraction of the work it outputs. An axle-back exhaust system will replace the components from the rear-axle back. While axle-back CORSA exhausts will provide some slight performance gains, their primary focus is to influence your exhaust notes. Different axle-back exhausts will offer different exhaust notes, so it's best to browse our entire selection to find the sound most suited for your vehicle.

The first widespread introduction of catalytic converters was in the United States automobile market. The exhaust system is crucial to a car’s performance, especially the catalytic converter which can go bad if it’s overworked. A stock exhaust system strives to minimize the car’s materials while maximizing space. This means that the exhaust system’s performance can suffer, having to work harder with less horsepower.

#19680 includes all the hardware necessary for do-it-yourself installation. Extensive testing on our in-house dyno has been used to ensure this SPEQ Series truck exhaust system not only sounds impressive but also has the performance bite to match its newfound bark. Consent to receive text messages for these purposes is not a condition of any purchase, service, or sweepstakes entry. So, if you are okay with the sound and performance then you have no need to replace your original exhaust system. OEM exhaust systems on the other and have crush-bent tubing made of normal steel.

From the inception of the small block Cobra, Carroll Shelby intended to build a race version of his lightweight roadster; its ultimate iteration was the 289 FIA roadster. Special Edition Shelby F-150 Super Snake celebrates Carroll Shelby's passion for performance trucks. Shelby American is celebrating the 100th anniversary of Carroll Shelby's birth with a performance street truck to honor the ledged.

To maintain catalyst efficiency, the air–fuel ratio must stay close to stoichiometric and not remain rich or lean for too long. All of Milltek's performance exhaust systems are manufactured from T304L stainless-steel; giving you the satisfaction of knowing that Milltek's products are meant to last within some of the toughest environments. T304L is a highly durable form of stainless-steel that is far less susceptible to degradation and discolouration than many others of its kind, while it will last almost indefinitely. If you are looking for something a little more unique, you can opt for a split rear or custom cat back exhaust system design. The split models feature an exhaust pipe that, as the name suggests, splits into two side-by-side pipes at the end, often with polished muffler and exhaust tips to really make a visual impact. The wider pipes of a cat back exhaust system mean that your vehicle is able to breathe better.

The installation of a cat-back exhaust system is fairly easy, but this too depends on your vehicle’s make and model. But, compared to the alternative, they are the easiest way of improving your vehicle’s performance without breaking the bank. As a result, the engine gets to breathe better and so release more torque and horsepower.

This exhaust is going to sound the deepest and give you some nice pops and bangs, while also giving you real world WHP and TQ gains. We’ve seen as much as +12 WHP when we tested our turbo-back for the 2022+ Honda Civic! For this version, we do recommend a tune and a device like a Ktuner V2 or Hondata Flashpro to take full advantage. Since the OEM catalyst is replaced with the downpipe, the Turbo-back system is sold for Race Use Only. A cat-back exhaust system replaces the stock exhaust components from the catalytic converter back to the exhaust tips.

Catback exhaust systems are popular among car enthusiasts because they can improve the sound and performance of a vehicle. From classic American muscle cars to the newest off-road capable rigs, STILLEN has you covered. Browse our most popular performance car, truck and SUV exhaust systems to find the ultimate exhaust experience for your vehicle. If you’re looking to enhance the performance of your car, you may have heard the term "cat back exhaust" being thrown around and wondered what is a catback exhaust exactly.

By freeing up the restrictions in the exhaust system, a cat back exhaust can help your engine to breathe more freely. This, in turn, can lead to a significant increase in horsepower. If you love cars just as much as we do, then you know that one of the best upgrades you can make to your vehicle is a cat back exhaust. But if you're not familiar with this term, don't worry – Vandemon Performance is here to break it down.

This quality material will ensure that your Cat-Back system will last through any harsh conditions. A cat back exhaust system is a form of car exhaust that includes the catalytic converter. This type of system is often used by those who want to improve their car's performance, as it can help to increase power and efficiency.

Our straight-through brushed-finished mufflers are configurable to your desire, smoothing the exhaust note to a deep growl, without adding restrictions, rasp or drone. Strong high-quality bracketry and OEM-style clamps hold the system steadily in place, making the install or removal a snap, and fitment simple, yet precise. A cast 3" to dual 2.5" rear splitter creates an ultra-smooth transition, steadily feeding exhaust gasses out of the system, while looking tidy from under the rear bumper. Finally, removable 4" polished slash-cut exhaust tips finish the system, adding a classy motorsport-inspired touch to the rear of the vehicle. In addition to high-quality materials and components, the design of each high-performance exhaust system allows for easy, bolt-on installation right out of the box. CORSA exhausts require no welding and can mount directly to your factory connections.

Shelby American is pushing the latest generation Shelby GT500SE supercar to new levels. As the first Carroll Shelby Signature Edition version for this model, the car delivers sizzling styling, razor sharp handling and an additional 40 horsepower. The 2024 Shelby Super Snake is the pinnacle of our performance cars based on Ford's next generation S650 Mustang sports car. Gases are pulled from the cylinder head by the exhaust manifold, at which point they are removed via the exhaust at the rear of the vehicle.

At Thermal R&D Performance, we have been developing quality aftermarket exhaust systems for decades. The materials we use are generally an upgrade from OE metals, and we incorporate our True Helmholtz Technology to eliminate cabin drone. This eliminates unwanted sound without restricting airflow needed for improved performance. Some three-way catalytic converter systems have air injection systems with the air injected between the first (NOx reduction) and second (HC and CO oxidation) stages of the converter. As in two-way converters, this injected air provides oxygen for the oxidation reactions.

The package is designed to maximize the performance of the Ford Mustang giving the vehicle a wider track with all the necessary suspension and braking systems to balance out the package. Introducing the 2024 Roush F-150, the perfect fusion of bold design, aggressive styling and high-performance upgrades. Each of the twin pipes are 50mm and the junction is 60mm but it quickly necks down to 50mm as it enters the center resonator. The resonator is a straight through 50mm perforated tube and some high frequency sound is absorbed.

A cat-back exhaust system is one of the best ways to improve your car's performance. It replaces the stock cat-back exhaust system and gives your car a more aggressive sound. Perhaps the most significant benefit is the increased power that it can provide.

The only difference is that it features straight perforated pipes. The original exhaust systems focus more on just reducing the sound and not shaping it to give it that desired deep growl. One function shared with both the axle-back and the cat-back exhaust systems are shaping your vehicle’s tone.

Most designs of the time therefore included secondary air injection, which injected air into the exhaust stream. This increased the available oxygen, allowing the catalyst to function as intended. Cat-back exhaust systems replace every component behind the catalytic converter, including most piping, mufflers, resonators, and tailpipes.

Less restrictive catalytic converters paired with a cat-back exhaust system will offer high performance and power. Though, the level of horsepower gained is not constant across all cat-back systems. It depends on the quality and performance of the catalytic converters. Because of the better flow of exhausts resulting from the mandrel-bent tubing and the larger diameter piping, cat-back exhaust systems manage to offer better performance. IE offers catback, downpipe, and midpipes upgrades to replace individual sections of your exhaust. Installing variations of these parts allows you to dial in your exhaust volume to your preference, from sporty to aggressive.

As an added bonus, cat-back systems include all of the necessary parts to replace your existing exhaust. The only costs you need to worry about are the kit itself and installation. Installing one of our cat-back exhaust systems is one of the best upgrades you can do on your Ford Maverick. Cat-back exhaust refers to what's in "back" of the "cat," or catalytic converter. It refers to the components that run from the rear outlet of the catalytic converter all the way back to the exhaust tip.

You can also add other upgrades to give your Charger an extra performance boost. Visit the AmericanMuscle headers and exhaust accessories pages to find parts that fit your new cat back system. Mishimoto offers a wide selection of exhaust systems, including cat-back exhausts, performance exhaust systems, and aftermarket exhaust options, designed to enhance your vehicle's performance, sound, and style. Our exhaust systems are engineered with precision and constructed using high-quality materials to deliver improved exhaust flow, increased horsepower, and an enhanced driving experience. Enhance the sound and performance of your Subaru with our premium cat back exhaust systems. Designed to replace the factory exhaust system from the catalytic converter rearward, these cat back exhausts offer a deeper, more aggressive exhaust note while reducing restriction for improved airflow.

Fine-tune your ride for the best performance and aesthetic today. Steeda offers the largest complete line of ford focus headers-based parts and accessories for your build and is considered the largest privately owned Ford performance-based operation in the world. If you've been searching for the perfect place to purchase Ford automotive performance parts for your vehicle, then you're at the right place!

Installation was super easy, and did it myself with only ramps. When IE claims 'no-drone' they really mean it - the sound is perfect! The youtube videos do not do a good job capturing the sound quality, but trust me, it's the best overall setup for your car at a reasonable price point. Enjoy a tuned and enjoyable exhaust note without any raspy leaks ruining the show. Our exhaust system assembles with our wide-width stretch clamps designed to seal and pull your exhaust connections together.

The bolstered heated front seats and contoured rear bench are upholstered in Onyx and Red leather. Appointments include a Blaupunkt 11-speaker sound system, a CD stereo, cruise control, a leather-wrapped shift lever, and automatic climate control. Whether you're seeking Upgraded Turbochargers, Axle-Back exhaust systems, Coilovers, or SubiSpeed Headlights we have you covered. The truck is based on the F-150 Lariat 4x4 SuperCrew and Shelby plans to limit production to 800 examples for the 2024 model year. Pricing starts at $130,000 for the naturally aspirated version and $139,995 with the supercharger attached. The urea solution is also referred to as diesel exhaust fluid (DEF).

If you've got questions about cat-back exhaust systems, pipe diameters, muffler type, or anything else, talk with our product specialists. All 1995 model year vehicles, and all 1992 model year or earlier vehicles. All model year vehicles that were manufactured with EPA or Federal emissions certification. Exhaust gases from the cylinders are collected in the exhaust system to prevent harmful fumes from entering the vehicle.

The DroneTrap system is wrapped up in our stamped multi-wall resonator that reinforces the housing inside and out. This high level of manufacturing protects the resonator from warping or splitting at the welds under exhaust movement. Prices stated here are only for sales within the continental United States and ordered via the ROUSHperformance.com web site. Prices for other territories and countries may vary due to shipping fees, duties, and other factors.

Proposition 65 requires California to publish a list of chemicals known to cause cancer, birth defects or other reproductive harm. This list, which must be updated at least once a year, has grown to include approximately 900 chemicals since it was first published in 1987. RES is but one of many great vendors of parts for your car’s exhaust system. Entice customers to sign up for your mailing list with discounts or exclusive offers. I watched a ton of videos and finally found one from Edge Autosport that went through 6 different variations of ETS setups.

Cat-back exhaust systems replace all the components after the catalytic converter, sometimes referred to as the cat. Now you can upgrade your downpipe or mid-pipe depending on your applications. Some cat-back systems will include a mid-pipe depending on your cat layout. And when you want to make more power and take your vehicle to the next level, then you will be ready for an exhaust manifold. Available only from Mallett Performance Cars, this exhaust system is made from 304 stainless steel and features the highest quality mufflers and resonators.

Since 2003, we have specialized in building BMW M-models (and Tesla) with a refined selection of industry-leading, high quality products. Our 8,000 sq/ft installation facility and shipping headquarters is located in Anaheim, California. IE's advanced DroneTrap technology captures the pulse waves responsible for your B9 3.0T engine's exhaust note and draws them into dual mathematically tuned resonators. The internal ports are engineered to resonate these waves against each other in a process that selectively cancels out those responsible for annoying drones.

All are capable of delivering a race-inspired exhaust note along with more power and torque. And this is why cat-back exhaust systems are considered to be one of the best performance modifications that are rewarding in power and sound and are highly effective for all driving purposes. Aside from maximizing your sound gains, the RSC® technology in every CORSA high-performance exhaust allows for a completely free-flowing air path to optimize your performance with every drive.

Cat back exhaust systems are a great way to enhance the performance and look of your vehicle without having to take out a small loan. An average exhaust will start at around $300 and can go up to anywhere around $3000. You will be able to find a cat back exhaust system for just about every make and model of a vehicle, and they are easy to install, making them great for people who love a bit of DIY.

This will improve the throttle response and acceleration in naturally-aspirated cars. The same reaction will be found in cars with forced induction with the addition of less turbo lag or supercharger response. Cat-Back exhaust systems are the most popular, coveted, and sought-after modification that enthusiasts will initially perform because of the main reason, and that is the sound. All of the brands we carry offer exhaust systems that are the result of decades of research and development.

It typically includes a rear pipe, resonator, and muffler that all attach after the last catalytic converter. The turbo-back system is the most complete system you can buy. It replaces all of the components that the previous two systems that we’ve talked about and also upgrades the downpipe. The downpipe is the first piece of exhaust piping that comes after the turbocharger and it also houses the catalytic converters on all L15 powered 1.5T Civics and Integras. From a sound and performance perspective, you’re going to get the most of both compared to the other two versions mentioned before.

Invidia offers products known for their outstanding quality, and each finished piece is a work of art that sets them apart from the competition. For anyone looking to take their vehicle to the next level, Invidia is a name to remember. So, a cat back is used to indicate an upgrade to the stock exhaust system. And anyone looking to improve their ride should strongly consider a cat back exhaust system. This pipe will connect your mk1 downpipe that we sell for  1.8t, vr6, or aba 2.0, to the catback exhaust system. Therefore you need to check with your local state laws for legality.

It's more than our precision-fit or full engine-to-tailpipe product offering, Walker sets the standards. From mild rumble to wild roar, upgrading your exhaust will improve the sound of your truck and help it to stand out from the pack. This direct-fit SPEQ Series system bolts on to your Tacoma easily thanks to the extensive use of 3D scanning during development to ensure OEM-like fitment.

Beyond these incremental advantages, there’s not much to tell cat-back and regular exhausts apart, as they are commonly made from the same types of materials in roughly the same shape. Most newer vehicles have electronic fuel injection systems, and do not require air injection systems in their exhausts. Instead, they provide a precisely controlled air-fuel mixture that quickly and continually cycles between lean and rich combustion. Depending on your make and model, cat back exhaust systems can lead to an increase in fuel economy. The engine doesn’t have to work as hard pushing exhaust gases through the piping which reduces its load and leads to higher efficiency and MPG. For car enthusiasts and performance drivers, upgrading the exhaust system of a vehicle is a no-brainer.

This picture is looking at the manifold end has a 60mm inlet ID and a 3 bolt flange where the outlet end has a 2 bolt flange and a 50mm outlet ID. Increasing your engine’s torque output gives you the power you need to haul heavy payloads and tow trailers, boats, campers, and more. The Carven-TR Series Performance Muffler delivers a deeper sound with a lower tone. Bradley’s Auto Service is proud to be affiliated with TechNet, a network of more than 12,000 locally owned repair shops that are focused on delivering quality care to the communities they serve. When you have any kind of automotive work done by us or another TechNet-affiliated shop, you are covered nationwide.

When the exhaust mode is placed in "Sport" mode the exhaust system broadcasts an "Xtreme" level sound 6 decibels louder than the stock exhaust system. As the driver adjusts the exhaust mode to the "Normal" level, the exhaust produces an exhaust note more closely resembling a CORSA "Sport" level exhaust note. At Mishimoto we offer a variety of products such as intercoolers, catch cans, cold air intakes and more. Trust in Mishimoto's expertise and commitment to quality to deliver exceptional products for all your automotive needs. Mishimoto exhaust systems utilize high-flow mufflers for minimal flow restriction.

Check out our cat back exhaust category and you’ll find systems that are built from stainless or aluminized steel. They also come in different tubing diameters to deliver varying ranges of exhaust volumes. Some of our exhaust kits even come with resilient powder coatings, so you can get an upgrade that matches your Charger’s appearance. Thanks to the large selection of products at AmericanMuscle, you can definitely purchase a cat back exhaust that can bring out your vehicle’s true high-performance potential.

I do live in a residential community and want to keep things civil with my neighbors...so I went with the resonated/muffled setup. Orders of $299.99 or more ship free within the continental U.S.Shipping to Alaska and Hawaii is additional and not included.We do not ship international at this time. Enter your email address above, to be notified of new products released. Sign up to our newsletter and stay up to date on all the latest news, products and events.

Typically, this includes the pipe connecting the pipe from the catalytic converter to the muffler, the muffler, and the tailpipe or exhaust tips. Because these types of exhaust systems are installed after the emissions monitoring systems of a vehicle, they won’t impede its ability to measure emissions. However, you must be aware of your local noise regulations and adhere to them. With relatively short install times when using a high-quality system from MagnaFlow, exhaust modifications can yield the instant gratification of your ride sounding as fast as it looks. When you purchase an aftermarket exhaust system like a cat-back exhaust, you're in control of horsepower and sound output as pipe diameter and muffler type are in your hands.

This style of clamp design is popular in high-end OE applications and is known for long-term reliability. You can change the look of your Jeep too, with everything from polished stainless steel to full black exhaust kits, you can pick just the right look for your jeep. Depending on the year of your Jeep you might even be able to get a single or dual exit exhaust. You can choose your favorite exhaust system from our three collections, the GRiP Exhaust, N-II Exhaust, or the DT-S Exhaust.

Everything you love about our MK7 Golf range has been re-engineered to suit MK7.5. Enjoy an unparalleled experience, power and sound output coupled with a seamless fit. Trucks are all about dependability and capability, which is why MagnaFlow engineers every one of our durable, corrosion resistant stainless-steel exhausts to last the lifetime of your vehicle. One of the things you would appreciate about the axle-back exhaust system is that it offers better sound improvement.

In layman’s terms, a catback exhaust system provides a smoother, more streamlined path for exhaust gases to exit your car, allowing your engine to work more efficiently. When catalytic converters were first introduced, most vehicles used carburetors that provided a relatively rich air-fuel ratio. Oxygen (O2) levels in the exhaust stream were therefore generally insufficient for the catalytic reaction to occur efficiently.

Therefore, they are placed as close to the engine as possible, or one or more smaller catalytic converters (known as "pre-cats") are placed immediately after the exhaust manifold. Founded in 1988, Steeda is the leader in Ford performance products. We specialize in the engineering and manufacturing of parts for the Ford Mustang, Bronco, Bronco Sport, Explorer, Escape, Fusion, Focus, Fiesta, Ford Trucks, and more!

Noticeable gains will be noticed in the initial throttle response, with reduced turbo lag. Engine movement and exhaust weight are transferred into the exhaust hangers, which puts a lot of stress on the mount brackets. IE's catback system is manufactured with multi-point and boxed-in hanger mounts designed to stand the test of time. Drive confidently knowing your exhaust is securely mounted and protected against annoying rattles or breaks. All piping is constructed of mandrel-bent T304L stainless steel to offer superior corrosion resistance.

This is a direct drop-in and can be installed at home or at the shop. That’s why we carry a wide lineup of sport exhaust systems, from individual pieces to full kits, made by some of the best manufacturers in the industry. We take exhaust so seriously that we also make our own branded exhaust systems in our own facility. We use 304 stainless steel for extra durability and life, and ensure every component is forged to fit your vehicle. Cat-back exhaust systems have more efficient gas flow, yielding increased engine performance, thanks to their larger exhaust tubes and mandrel bends. As a result, your car will be able to breathe better and produce more power.

Next we have the option we refer to as the Cat-back system (sometimes also known as "with Front Pipe" exhaust). One of the most noticeable changes after installing a cat-back exhaust system is the sound. The exhaust note becomes deeper and more pronounced, giving your vehicle a more aggressive tone. The specific sound varies depending on the muffler and pipe design, allowing drivers to choose a system that matches their preference for loudness and pitch.

Follow us on Facebook, Instagram, YouTube and Twitter to stay up to date on our latest products, projects, and adventures. Join the conversation and show off your ride with #MagnaFlow for a chance to be featured. Overall, cat back systems are relatively low-maintenance and easy to keep in good working order. There are a few common problems that can occur with cat back systems, but fortunately, they are relatively easy to fix.

All joints are hand TIG welded using precise fixtures and tooling. We take great pride in knowing your new exhaust will sound remarkable and stand the test of time. Stand out from the crowd with oversized 90mm quad slash-cut exhaust tips. These aggressive-looking tips fill the factory exhaust cutouts for that high-end sporty look. Over 20 years of expertise have cemented TruBendz's reputation for excellence. Our commitment to high-quality materials and craftsmanship ensures that you get the best bang for your buck.

But with so many options available, it's easy to get lost in the world of aftermarket exhaust systems. While some companies may try to lure customers with an attractive price tag or flashy branding, it's quality of performance, sound, and construction that truly sets a great brand like Invidia apart from the rest. Transform your vehicle with the Roush Performance F-150 Cat-back Exhaust System, an ideal replacement for your factory exhaust system. Crafted from robust, corrosion-resistant T-304 stainless steel, this system features high-flow mandrel bends to enhance exhaust flow efficiency. Experience the thrill of enhanced acoustics and performance with this premium upgrade for your F-150. Banks patented exhaust systems enhance power, fuel economy, and sound by removing all airflow restrictions.

The remaining waves produce the deepened and enriched exhaust acoustics you love. Stillen offers a variety of exhaust systems for many vehicles, both foreign and domestic. The muffler is a glass filled, large chamber design that provides the optimal amount of exhaust velocity for the engine while producing a great low rumble sound - without any annoying buzzing, "racer" sound. The high clearance fitment dramatically reduces the risk of getting hung-up on obstacles when off-roading. We’ve been helping customers with performance upgrades since 2006, and have a staff full of people who can help answer your questions. Our customer service — from our low prices to our fast shipping — has earned us a reputation with a legion of fans.

Each cat-back exhaust system is made from high quality components and assembly so you can get the performance you want at a price you can afford with the assurance you need. Please note Quad Tips are available with optional Carbon RR Racing Tips! (see photo of our new tips in the image library for this product)This is our signature full cat-back exhaust system for Lexus ISF.

They both improve your engine’s tone and give it that deep rumble loved by every motor enthusiast. Getting a cat-back exhaust system is definitely the more budget-friendly option. Other benefits of aluminized steel is they are lightweight and very workable.

Cat-back exhaust system kits come standard with tailpipes, a performance muffler and exhaust tips. The inclusion of our wider, mandrel-bent tailpipes means cat-back exhausts are your go-to for increasing your performance gains along with boosting your sound. While horsepower and torque gains vary from vehicle to vehicle, you can expect anywhere from a percent gain in horsepower and torque after installing a cat-back exhaust system.

Because the engine won’t generate as much fumes and doesn’t need to work as hard to eliminate or minimize the fumes, your car will run better, saving you mileage. A benefit like this will improve the longevity of your car and even save you money at the gas pump. At Bradley’s Auto Service in Red Bank, NJ, we can build a completely custom exhaust system for your vehicle, including cat-backs. We will work with you to create your exhaust exactly the way you want it, with any combination of look, sound, feel, power, or muffler at your fingertips.

Combined with our five different tip options, we've got you covered. We’ve had decades of experience perfecting exhaust style and technology and have developed custom exhaust systems considered too ‘niche’ by competitors. Many exhaust manufacturers use 400 series stainless steel to reduce costs and pad their profits. Additionally, the Maverick systems by Thermal offer a range of upgraded tip options that owners can choose from or change over time. Getting an upgraded cat-back exhaust system for your truck can enhance your performance and produce a great sound. Then there’s poor fitment and the dreaded drone that all too often accompanies aftermarket exhausts.

This is the 3rd Gen Toyota Tundra Borla S-Type Cat Back Exhast with Chrome Dual Tips. Borla manufacturers some of the best Toyota Exhaust systems, and this S-Type 2022 6.7 powerstroke delete+ Tundra Exhaust is no different, featuring the Merge X-Pipe for increased performance adn improved sound. The Carven-R series Performance Muffler delivers an aggressive sound with a refined tone. This unique pack-less (Patent# D802,507) muffler design is one of its kind. Stand out from the crowd with a performance exhaust system that sounds great. Save big on that signature MBRP sound during Pick Up Your Sound.

As a result, our popularity has increased, and we work tirelessly to maintain our quality systems while fulfilling orders. Please be aware that while we typically exceed our estimated wait times, we have been successfully operating for three years and no customer has ever been left without their system, or a cancellation/refund. At Rae, we are expanding our team and investing in additional resources and machines to ensure we stay at the forefront of innovation. With our ambitious plans, we are on track to meet demand and increase our inventory of premium parts by the end of the year. Please note that purchasing this product is agreeing to understand this concept. Amplify your vehicle's performance and sound with Full-Race's premium Exhaust systems - reliable power and efficiency harmonize with a brand that’s trusted for quality and performance.

The difference in fuel economy is, however, more obvious while driving on a freeway. They also do not offer the best performance due to many reasons. If you're looking for an off-road exhaust with maximum clearance and an extremely&nbs.. Sign up for the IE mailing list and stay up to date on new products, sales, giveaways, and promotions.

Aftermarket custom cat back exhaust systems increase the efficiency of an exhaust system because of the mandrel-bent turns and reduction in back pressure. They are the popular choice when it comes to aftermarket exhaust systems as they offer reliable performance and sound without having to buy a new catalytic converter. They are also well-suited to those who like to handle their own installation!

Straight-through, or flow-through, mufflers have perforated baffles and packing material that provides a conservative level of sound absorption while still keeping sound output moderately loud. Glasspack mufflers perform similar to resonators due to their design and lack of sound-absorbing packing material, so they tend to be louder and higher pitched. For compression-ignition (i.e., diesel) engines, the most commonly used catalytic converter is the diesel oxidation catalyst (DOC). This catalyst converts particulate matter (PM), hydrocarbons, and carbon monoxide to carbon dioxide and water. These converters often operate at 90 percent efficiency, virtually eliminating diesel odor and helping reduce visible particulates. These catalysts are ineffective for NOx, so NOx emissions from diesel engines are controlled by exhaust gas recirculation (EGR).

The buyer is solely responsible for obtaining the permissions where applicable required by the applicable law for the intended purposes/usage. In no event a whatsoever claim shall be constituted by the buyer against REMUS and its affiliates arising from or in connection with required approvals for public road usage. Take your stock or modified Colorado/Canyon to the next level with a Mallett Performance Cars exhaust system today.

Featuring virtually indestructible 100% stainless steel, our patented TorqueTube headers maximize exhaust extraction to haul you up the grade. This Takeda cat-back exhaust system by aFe POWER delivers superior performance, quality, and good looks. By replacing the rear section of your exhaust with a quality cat-back car performance exhaust system, you can reduce the backpressure and allow your engine to cycle with more speed and efficiency. Thanks to their larger diameter pipes and high-quality mandrel bends, a good cat-back exhaust system will increase the efficiency of your car’s exhaust system, and with increased efficiency comes increased power. The exhaust system in your car directs fumes away from yourself and your passengers, improves engine performance and fuel consumption, and controls cabin noise.

Make sure your Subaru, Nissan, Honda, or Toyota is outfitted with a top notch exhaust system from Racing Exhaust System. Some are ideal for normal vehicles while others are better for high-performance engines. Products manufactured by REMUS without (EC-)approval are only eligible for usage at motor sport events or tests within the meaning of KFG 1967.

These look like standard mufflers with a VERY unusual side entry rear exit configuration. Notice the heat discoloration at the intersection where the split occurs.Heat discoloration shows up where there is a flow restriction. Notice also the heat discoloration just after the pipes enter the silencers. It is AMAZING the engine makes the power it does through this congestion. Features Only 10 lbs [catless and non resonated version] 304 stainless steel piping Smooth air flow for maximum horsepower Compatible with both manual and automatic transmissions TIG welded to perfection... The main functions of exhaust systems are increasing horsepower and improving your engine sound.

As a result, the glass pack mufflers end up producing sounds that are more aggressive and louder than the straight-through muffler. This is a little bit different from most original exhaust systems. Today we’ll focus on the cat-back exhaust systems and what makes them stand out. There are the header-back, turbo-back, axle-back and cat-back systems.

Dual Magnaflow wide open mufflers with quad 3.5" exhaust tips, slightly louder and deeper than standard Borla. This upgrade option retains the large Borla resonator and replaces Borla mufflers with dual Magnaflow mufflers and quad tips. Borla is a great exhaust, but with this upgrade your back will look much better with the large aggressive oval quad tips and will sound better too! Cat-back exhaust systems refer to all of the components that exhaust gasses flow through after exiting the vehicle’s catalytic converter.

All performance exhaust systems are designed with you in mind, and we cater to an ever-expanding range of vehicles. Milltek believes in continuous evolution, and their research & development team work throughout the year to deliver the most in demand solutions to all your performance exhaust requirements. All products are made in the UK and distributed to more than 90 countries worldwide, making Milltek Sport one of the most accessible performance aftermarket brands on the market. If you're looking to customize your vehicle's exhaust system, Mishimoto also offers a range of aftermarket exhaust options. These exhaust systems are designed for specific vehicle models and provide a combination of performance, sound, and visual enhancements.

Namely, it replaces the rear axle-back and tips and then a portion of what we refer to as the mid-pipes. This system is emissions friendly and doesn’t require any tuning. In New Jersey, vehicles must pass emissions testing to ensure they meet environmental standards. Since cat-back exhaust systems do not modify the catalytic converter or engine management system, they generally do not affect a vehicle’s ability to pass emissions testing.

A cat back exhaust system is one of the most popular aftermarket upgrades for performance-minded drivers. When deciding which type of exhaust system to choose, it is important to consider your needs and budget. If you are looking for maximum power and efficiency, a cat back exhaust may be the best option. However, if you are more concerned with cost and weight, a standard system may be a better choice. A cat back exhaust is one of the most popular upgrades for car enthusiasts.

The precious metals inside the converter, including platinum, palladium, and rhodium, are extracted. Ford Motor Company and Shelby American collaborated to create a stunning high performance concept vehicle based on the exciting and innovative Ford Mustang Mach-E GT platform. The big block Shelby Cobra is considered by many to be the most iconic American sports car in history. When GM began to work on a new big block Corvette and Ferrari increased the power of the V12 powered GTO's, Shelby and Ford Motor Company decided to shoehorn the mighty 427 FE motor into the Cobra. By combining Ford's incredible 2014 6.7 cummins delete kit-liter Power Stroke® turbo diesel churning out 1,050 lb.-ft. Of torque with a Shelby tuned advanced off-road suspension system, the three-quarter ton truck delivers both serious off-road capabilities with best-in-class towing.

This modification includes the pipes, muffler, and sometimes the resonator. The term "cat-back" itself signifies that everything behind the vehicle’s catalytic converter is being upgraded or replaced. Milltek's Sport Catback Exhaust Systems are designed to compensate for the sound reducing qualities from the particulate filter and significantly improve the sound aesthetic of the exhaust system.

A spare set of 19″ Y-spoke alloy wheels is included in the sale, and they are shod with Bridgestone tires. The car is finished in Panther Black Metallic (80U) and features a GXP-specific front bumper cover and rear diffuser as well as a sunroof, fog lights, dual hood scoops, fender vents, and a rear spoiler. Imperfections are noted on the decklid and on a door and are also shown in the gallery. Our expansive inventory of Subaru performance parts ensures your vehicle not only performs at its peak but is also supported by our unparalleled customer service. At SubiSpeed, we understand that upgrading your Subaru is not just about selecting the right parts; it's about having a trusted partner every step of the way.

Finished in Panther Black Metallic over Onyx and Red leather, the car is powered by a 6.2-liter V8 linked with a six-speed automatic transmission and a limited-slip differential. Purchased by its current owner in February 2022, this G8 GXP is now offered with a reproduction window sticker, service manuals, a car cover, the removed exhaust system, a spare set of wheels, and a Michigan title. A catalytic converter is an exhaust emission control device which converts toxic gases and pollutants in exhaust gas from an internal combustion engine into less-toxic pollutants by catalyzing a redox reaction. Catalytic converters are usually used with internal combustion engines fueled by gasoline or diesel, including lean-burn engines, and sometimes on kerosene heaters and stoves. Whether you’re accelerating up a highway on ramp or passing slower traffic, improved acceleration lets you get up to speed more quickly. Gain horsepower, increase torque, and give your truck a more aggressive exhaust note with a new exhaust system.

Cat-back exhaust systems will include any pipes that run from the catalytic converter to the muffler, the muffler itself, any pipes that may run from the muffler to the exhaust tips, and the exhaust tips themselves. Some cat-back exhaust systems have a muffler delete, which means no muffler is included. This is typically found on vehicles that function primarily for off-road use; it's not standard on daily driver vehicles and is even illegal in some states.

A dual exit on the other hand, is just a single exhaust system but with two exhaust tips. This is because, with a cat-back exhaust system, you will experience a significant increase in your fuel economy. The tone provided by different cat-back exhaust systems varies from one system to another.

The amount of horsepower gained from installing a cat-back exhaust system varies by vehicle and the system’s design. However, when combined with other performance enhancements, the gains can be more significant. The primary goal of a cat-back exhaust is to reduce back pressure, allowing your engine to breathe better and operate more efficiently. The factory exhausts come in mandrel bent tubes made of stainless steel or aluminized steel. Besides offering longer durability, the construction also ensures there’s free flow of gases. To improve this, you can opt to replace some parts of the exhaust system using aftermarket performance exhaust systems.

We want to make sure the part fits your specific vehicle so we need a little more information from you. You can find out by inspecting the emissions sticker that is located in your engine compartment.

Because the success of a catback exhaust system depends on various factors – like catalytic converter restrictions, engine power, etc. – there’s no easy way to calculate how much horsepower you stand to gain. If you have a restrictive exhaust, then a cat back exhaust could massively improve your car’s performance, and contrastingly, if your exhaust already flows well, then a cat-back won’t be much of an upgrade. In Colorado, it is illegal to select a catalytic converter for installation based solely on vehicle weight and engine size. Converters in this catalog are based on Executive Orders issued by the California Air Resource Board and must be used in accordance with this information.

Another difference is with the material used in the cat-back exhaust system against that in stock exhaust systems. But the problem with a resonator is that it can cause restriction to the flow of the exhausts. In the end, this can end up lowering your vehicle’s performance. It is also more affordable and easier to install than other types of exhaust systems, including the cat-back exhaust system. Cat-back and axle-back exhaust systems are both aftermarket exhaust systems. A performance exhaust system, like the cat-back exhaust, allows for easy splitting into dual exhaust.

We match the exit size to the size exhaust you ordered, so if you are ordering this after the fact, please include the exhaust size you have in your order. Replaces the OEM catalytic converter with a free flowing pipe. Completely straight through (no bottleneck), free flowing mini-muffler and pipe. Replaces the OEM catalytic converter with a 3" metal substrate core high-flow performance cat and our mini muffler. The metal core is our highest flowing cat available and it will reduce... Rae is a very small 1000sqft shop, run by a dedicated team of two. Our motto, "Quality over quantity," drives everything we do and ensures the highest standards in every order.

In this article, we’ll explain what a catback exhaust system is, what it does, and why it’s different from your run-of-the-mill exhaust systems. There are seemingly endless available upgrades when looking to enhance vehicle performance. It certainly rings true when it comes to your vehicle’s exhaust system. One term that you’ve probably heard if you’re in the market for an aftermarket exhaust upgrades is cat-back exhaust. What exactly does it mean, and how does it change the way your vehicle performs? This 2009 Pontiac G8 GXP is one of approximately 1,830 examples produced, and it has 16k miles.

Shelby also gives the truck some off-road chops by installing a BDS 3.0-inch lift kit, Fox 2.5-inch internal bypass dampers, and performance rear traction bars. The truck also sits on a set of 22-inch Shelby wheels wrapped in 35-inch all-terrain tires. The new 2024 Ford Shelby F-150 packs up to 785 hp, or more power than many supercars. That's with an available supercharger for the truck's 5.0-liter V-8. Buyers can also opt for a naturally aspirated version where the V-8 keeps its stock 400-hp rating.

CORSA does not recommend or recognize purchases and installations on unspecified vehicles. ARK Performance is a leading manufacture that develops the best cat back exhaust systems, downpipes, test pipes, and hi-flow cats for all car enthusiasts. Using custom designed straight through mufflers for flow - without the noise level of a track car. From a company that’s as committed to your satisfaction as to sonic excellence. A catback exhaust system is a great way to improve the sound, performance, and emissions of your vehicle. If you are looking for a way to improve your vehicle, a catback exhaust system is a great option.

Or are you a more relaxed driver who takes the roads less travelled? Knowing your driving style will help you pick a cat back that not only sounds good but also performs well. Lastly, you need to decide what material you want your cat back to be made out of. If you're looking for a way to enhance your car's performance and style, a cat back exhaust may be the perfect solution. All 1993, 1994, 1996 and newer vehicles that were manufactured with California or 50-State emissions certification.